|
@@ -0,0 +1,123 @@
|
|
|
+/********************
|
|
|
+Toaster Project
|
|
|
+Rev 3
|
|
|
+Jian Song
|
|
|
+
|
|
|
+Functions:
|
|
|
+1. Drehschalter
|
|
|
+2. Auslösemagnet
|
|
|
+3. Temperatursensor
|
|
|
+4. Heizwendel
|
|
|
+5. Stoptaste
|
|
|
+6. LCD
|
|
|
+7. Kontrollanzeige
|
|
|
+*********************/
|
|
|
+
|
|
|
+void Drehschalter() { //function for calibration of the heating time
|
|
|
+
|
|
|
+ int Grades; //define the degrees of browning
|
|
|
+ unsigned long tmax = 60000; //define the max. heating time
|
|
|
+ Grades = analogRead(0); //read the data from pin A0 of analog input
|
|
|
+ if (Grades >= 0 && Grades <= 205) { //input range for A0 is from 0 to 1024(because of 10 bit ADC), define potentiometer as 5 steps
|
|
|
+ tmax = 10000;
|
|
|
+ }
|
|
|
+ if (Grades > 205 && Grades <= 410) {
|
|
|
+ tmax = 20000;
|
|
|
+ }
|
|
|
+ if (Grades > 410 && Grades <= 615) {
|
|
|
+ tmax = 30000;
|
|
|
+ }
|
|
|
+ if (Grades > 615 && Grades <= 820) {
|
|
|
+ tmax = 40000;
|
|
|
+ }
|
|
|
+ if (Grades > 820 && Grades <= 1024) {
|
|
|
+ tmax = 50000;
|
|
|
+ }
|
|
|
+
|
|
|
+}
|
|
|
+
|
|
|
+void Ausloesemagnet() { //function for magnet trigger
|
|
|
+
|
|
|
+ int Magnet = 11; //define the magnet
|
|
|
+ unsigned long t = 0; //define the runtime
|
|
|
+ pinMode(Magnet, OUTPUT); //set pin 11 as digital output
|
|
|
+ while (t < tmax) { //run the loop if the runtime is less then tmax
|
|
|
+ t = millis(); //returns the number of milliseconds since the Arduino board began running the current program
|
|
|
+ digitalWrite(Magnet, HIGH); //turn on the magnet
|
|
|
+ }
|
|
|
+ digitalWrite(Magnet, LOW); //turn off the magnet, if the loop is broken
|
|
|
+
|
|
|
+}
|
|
|
+
|
|
|
+void Temperatursensor() { //function for reading temperature in celsius
|
|
|
+
|
|
|
+ #include <OneWire.h> //use onewire library
|
|
|
+ #include <DallasTemperature.h> //use dallastemperature library
|
|
|
+
|
|
|
+ int tempsensor = 6; //define temperature sensor
|
|
|
+ double temperature; //define the temperature
|
|
|
+ double Tmax = 50; //define the max. temperature
|
|
|
+ OneWire onewirepin(tempsensor); //setup a onewire instance to communicate with any onewire devices
|
|
|
+ DallasTemperature sensors(&onewirepin); //pass our oneWire reference to dallas temperature
|
|
|
+ sensors.begin(); //start the library up
|
|
|
+ sensors.requestTemperatures(); //send the command to get temperatures
|
|
|
+ temperature=sensors.getTempCByIndex(0); //get the temperature from the first sensor only
|
|
|
+ if (temperature > Tmax) { //compare the current temperature and max. temperature. if higher than max. , set t as tmax, then that while loop condition in function of ausloesemagnet is not true anymore, so the while loop will be broken until reset.
|
|
|
+ t = tmax;
|
|
|
+ }
|
|
|
+
|
|
|
+}
|
|
|
+
|
|
|
+void Heizwendel() { //function for controlling the heater
|
|
|
+
|
|
|
+ #include <PWM.h> //use PWM library
|
|
|
+
|
|
|
+ #define PIN_OUTPUT 3 //define pin 3 as output of PWM
|
|
|
+ int D; //set the dutycycle for PWM(8 bit timer can provide a range from 0 to 255 steps for PWM)
|
|
|
+ int32_t frequency = 10; //set the frequency of PWM in hertz
|
|
|
+ InitTimersSafe(); //initialize all timers except for 0, to save time keeping functions(for UNO timer0 and timer2 are 8 bit, timer1 is 16 bit; pins 5 and 6: controlled by timer0; pins 9 and 10: controlled by timer1; pins 11 and 3: controlled by timer2)
|
|
|
+ bool success = SetPinFrequencySafe(PIN_OUTPUT,frequency); //sets the frequency for pin 3
|
|
|
+ D = map(analogRead(1), 0, 1023, 0, 255); //re-maps the range of analog input A1 from 0 - 1023 to 0 - 255
|
|
|
+ pwmWrite(PIN_OUTPUT, D); //use this functions instead of analogWrite on pin 3
|
|
|
+
|
|
|
+}
|
|
|
+
|
|
|
+void Stoptaste() { //function for the stop button
|
|
|
+
|
|
|
+ int S; //define the push button as stop button
|
|
|
+ S = digitalRead(2); //read HIGH or LOW digital signal from pin 2
|
|
|
+ if (S == HIGH) { //if the button is pressed, set t as tmax, then that while loop condition in function of ausloesemagnet is not true anymore, so the while loop will be broken until reset.
|
|
|
+ t = tmax;
|
|
|
+ }
|
|
|
+
|
|
|
+}
|
|
|
+
|
|
|
+void LCD() {
|
|
|
+
|
|
|
+ #include <LiquidCrystal.h> //use LCD library
|
|
|
+
|
|
|
+ LiquidCrystal lcd(13, 12, 10, 9, 8, 7); //initialize the library with the numbers of the interface pins
|
|
|
+ lcd.begin(16, 2); //set up the LCD's number of columns and rows
|
|
|
+ lcd.setCursor(0, 0); //set the cursor to column 0, line 0(line 0 is the first row, since counting begins with 0)
|
|
|
+ lcd.print("T="); //print "Temperature = "
|
|
|
+ lcd.print(temperature); //print temperature in celsius
|
|
|
+ lcd.print("`C ");
|
|
|
+ lcd.print("t="); //print "Time = "
|
|
|
+ lcd.print(millis()/1000); //print current runtime in seconds
|
|
|
+ lcd.print("s");
|
|
|
+ lcd.setCursor(0, 1); //set the cursor to column 0, line 1
|
|
|
+ lcd.print("D="); //print "Dutycycle = "
|
|
|
+ lcd.print((D*100)/255); //print current dutycycle in percent
|
|
|
+ lcd.print("% ");
|
|
|
+ lcd.print("tmax="); //print "max. runtime = "
|
|
|
+ lcd.print(tmax/1000); //print preset of max. runtime in seconds
|
|
|
+ lcd.print("s ");
|
|
|
+
|
|
|
+}
|
|
|
+void Kontrollanzeige() { //shows the status, if PWM is working
|
|
|
+
|
|
|
+ #define LED 5
|
|
|
+ analogWrite(LED, D); //put a LED and resistor between pin 5 and GND
|
|
|
+}
|
|
|
+
|
|
|
+
|